View M37736EHLXXXHP_287181.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

P
. . tion nge ifica to cha t pec al s subjec fin re a ot a is n limits his e: T ametric ic Not e par Som
IM REL
IN
Y AR
MITSUBISHI MICROCOMPUTERS
M37736MHLXXXHP
SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
DESCRIPTION
The M37736MHLXXXHP is a single-chip microcomputer using the 7700 Family core. This single-chip microcomputer has a CPU and a bus interface unit. The CPU is a 16-bit parallel processor that can be an 8-bit parallel processor, and the bus interface unit enhances the memory access efficiency to execute instructions fast. This microcomputer also includes a 32 kHz oscillation circuit, in addition to the ROM, RAM, multiple-function timers, serial I/O, A-D converter, and so on. Its strong points are the low power dissipation, the low supply voltage, and the small package. In the M37736MHLXXXHP, as the multiplex method of the external bus, either of 2 types can be selected.
qLow power dissipation (At 3 V supply voltage, 12 MHz frequency) ............................................ 9 mW (Typ.) qInterrupts ............................................................ 19 types, 7 levels qMultiple-function 16-bit timer ................................................. 5 + 3 qSerial I/O (UART or clock synchronous) ..................................... 3 q10-bit A-D converter .............................................. 8-channel inputs q12-bit watchdog timer qProgrammable input/output, output (ports P0, P1, P2, P3, P4, P5, P6, P7, P8, P9, P10) ............... 84 qClock generating circuit ........................................ 2 circuits built-in qSmall package ..................... 100-pin plastic molded fine-pitch QFP (100P6Q-A;0.5 mm lead pitch)
APPLICATION FEATURES
qNumber of basic instructions .................................................. 103 qMemory size ROM ................................................. 124 Kbytes RAM ................................................ 3968 bytes qInstruction execution time The fastest instruction at 12 MHz frequency ...................... 333 ns qSingle power supply ...................................................... 2.7-5.5 V Control devices for general commercial equipment such as office automation, office equipment, personal information equipment, and others. Control devices for general industrial equipment such as communication equipment, and others.
PIN CONFIGURATION (TOP VIEW)
75 P92/RXD2 74 P93/TXD2 73 P94 72 P95 71 P96 70 P97 69 P00/A0/CS0 68 P01/A1/CS1 67 P02/A2/CS2 66 P03/A3/CS3 65 P04/A4/CS4 64 P05/A5/RSMP 63 P06/A6/A16 62 P07/A7/A17 61 P10/A8/D8 60 P11/A9/D9 59 P12/A10/D10 58 P13/A11/D11 57 P14/A12/D12 56 P15/A13/D13 55 P16/A14/D14 54 P17/A15/D15 53 P20/A16/A0/D0 52 P21/A17/A1/D1 51 P22/A18/A2/D2
P91/CLK2 76 P90/CTS2 77 P87/TXD1 78 P86/RXD1 79 P85/CLK1 80 P84/CTS1/RTS1 81 P83/TXD0 82 P82/RXD0/CLKS0 83 P81/CLK0 84 P80/CTS0/RTS0/CLKS1 85 VCC 86 87 AVCC VREF 88 89 AVSS VSS 90 P77/AN7/XCIN 91 P76/AN6/XCOUT 92 P75/AN5/ADTRG 93 P74/AN4 94 P73/AN3 95 P72/AN2 96 P71/AN1 97 P70/AN0 98 P67/TB2IN/f SUB 99 P66/TB1IN 100
M37736MHLXXXHP
50 P23/A19/A3/D3 49 P24/A20/A4/D4 48 P25/A21/A5/D5 47 P26/A22/A6/D6 46 P27/A23/A7/D7 45 P30/R/W/WEL 44 P31/BHE/WEH 43 P32/ALE 42 P33/HLDA 41 EVL0 40 EVL1 VCC 39 VSS 38 37 E/RDE 36 XOUT 35 XIN 34 RESET 33 BSEL 32 CNVSS 31 BYTE 30 P40/HOLD 29 P41/RDY 28 P42/f1 27 P43 26 P44
P65/TB0IN 1 P64/INT2 2 P63/INT1 3 P62/INT0 4 P61/TA4IN 5 P60/TA4OUT 6 P57/TA3IN 7 P56/TA3OUT 8 P55/TA2IN 9 P54/TA2OUT 10 P53/TA1IN 11 P52/TA1OUT 12 P51/TA0IN 13 P50/TA0OUT 14 P107/KI3 15 P106/KI2 16 P105/KI1 17 P104/KI0 18 P103 19 P102 20 P101 21 P100 22 P47 23 P46 24 P45 25
Outline 100P6Q-A
P
. . tion nge ifica to cha t pec al s subjec fin re a ot a is n limits his e: T ametric ic Not e par Som
IM REL
IN
Y AR
MITSUBISHI MICROCOMPUTERS
M37736MHLXXXHP
SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
Input/Output port P10

Output port P9

Reference External data bus width selection input voltage input BYTE VREF
Data Buffer DBH(8) Data Buffer DBL(8)
Instruction Register(8)
Instruction Queue Buffer Q0(8) Instruction Queue Buffer Q1(8) Instruction Queue Buffer Q2(8)
Data Bus(Even) Data Bus(Odd)
P1(8)
P0(8)
P10(8)
P9(8)
AVCC
Incrementer(24)
Program Address Register PA(24) Data Address Register DA(24)
A-D Converter(10)
(0V) AVSS
P2(8)
Address Bus
CNVSS
Program Counter PC(16)
(0V) VSS
Program Bank Register PG(8)
Watchdog Timer
Timer TB2(16)
Timer TB1(16)
Timer TB0(16)
P4(8)
Incrementer/Decrementer(24)
VCC
Data Bank Register DT((8)
Bus method Reset input selection input RESET BSEL
Input Buffer Register IB(16)
Timer TA4(16)
Timer TA3(16)
Timer TA2(16)
Timer TA1(16)
Timer TA0(16)
Processor Status Register PS(11) Direct Page Register DPR(16)
M37736MHLXXXHP BLOCK DIAGRAM
XCOUT
Enable output E
XCIN
Stack Pointer S(16) Index Register Y(16)
RAM 3968 bytes
Index Register X(16)
Clock Generating Circuit
Accumulator B(16) Accumulator A(16)
Clock output XOUT
XCIN XCOUT
Clock input XIN
Arithmetic Logic Unit(16)
2
Input/Output port P8
ROM 124 Kbytes
P8(8)
Input/Output port P7
P7(8)
Input/Output port P6
P6(8)
Input/Output port P5
P5(8)
Input/Output port P4
UART2(9)
UART1(9)
UART0(9)
Input/Output port P3
P3(4)
Input/Output port P2
Input/Output port P1
Input/Output port P0
P
. . tion nge ifica to cha t pec al s subjec fin re a ot a is n limits his e: T ametric ic Not e par Som
IM REL
IN
Y AR
MITSUBISHI MICROCOMPUTERS
M37736MHLXXXHP
SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
FUNCTIONS OF M37736MHLXXXHP
Parameter Number of basic instructions Instruction execution time Memory size Input/Output ports Output port Multi-function timers Serial I/O A-D converter Watchdog timer Interrupts Clock generating circuit Supply voltage Power dissipation Input/Output characteristic Memory expansion Operating temperature range Device structure Package Input/Output voltage Output current ROM RAM P0 - P2, P4 - P8, P10 P3 P9 TA0, TA1, TA2, TA3, TA4 TB0, TB1, TB2 Functions 103 333 ns (the fastest instruction at external clock 12 MHz frequency) 124 Kbytes 3968 bytes 8-bit ! 9 4-bit ! 1 8-bit ! 1 16-bit ! 5 16-bit ! 3 (UART or clock synchronous serial I/O) ! 3 10-bit ! 1 (8 channels) 12-bit ! 1 3 external types, 16 internal types Each interrupt can be set to the priority level (0 - 7.) 2 circuits built-in (externally connected to a ceramic resonator or a quartz-crystal oscillator) 2.7 - 5.5 V 9 mW (at 3 V supply voltage, external clock 12 MHz frequency) 22.5 mW (at 5 V supply voltage, external clock 12 MHz frequency) 5V 5 mA External bus mode A; maximum 16 Mbytes, External bus mode B; maximum 1 Mbytes -40 to 85 C CMOS high-performance silicon gate process 100-pin plastic molded fine-pitch QFP (100P6Q-A;0.5 mm lead pitch)
3
P
ion. hange. icat ecif ct to c l sp fina re subje a not sa is is ric limit t : Th tice arame No e p Som
M ELI R
IN
Y AR
MITSUBISHI MICROCOMPUTERS
M37736MHLXXXHP
SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
PIN DESCRIPTION
Pin Vcc, Vss CNVss
_____
Name Input/Output Power source Apply 2.7 - 5.5 V to Vcc and 0 V to Vss. CNVss input Reset input Clock input Clock output Enable output Input Input Input Output Output
Functions
RESET
XIN XOUT
_
E
BYTE
BSEL
External data bus width selection input Bus method select input Analog power source input Reference voltage input I/O port P0
Input
Input
AVcc, AVss VREF P00 - P07
This pin controls the processor mode. Connect to Vss for the single-chip mode and the memory expansion mode, and to Vcc for the microprocessor mode. When "L" level is applied to this pin, the microcomputer enters the reset state. These are pins of main-clock generating circuit. Connect a ceramic resonator or a quartzcrystal oscillator between XIN and XOUT. When an external clock is used, the clock source should be connected to the XIN pin, and the XOUT pin should be left open. This pin functions as the enable signal output pin which indicates the access status in the internal bus. In the external bus mode B and the memory expansion mode or the microprocessor mode, ___ this pin output signal RDE. In the memory expansion mode or the microprocessor mode, this pin determines whether the external data bus has an 8-bit width or a 16-bit width. The data bus has a 16-bit width when "L" signal is input and an 8-bit width when "H" signal is input. In the memory expansion mode or the microprocessor mode, this pin determines the external bus mode. The bus mode becomes the external bus mode A when "H" signal is input, and the external bus mode B when "L" signal is input. Power source input pin for the A-D converter. Externally connect AVcc to Vcc and AVss to Vss. This is reference voltage input pin for the A-D converter. In the single-chip mode, port P0 becomes an 8-bit I/O port. An I/O direction register is available so that each pin can be programmed for input or output. These ports are in the input mode when reset. In the memory expansion mode or the microprocessor mode, these pins output address (A0 - A7) ___ ___ ____ at the external bus mode A, and these pins output signals CS0 - CS4 and RSMP, and addresses (A16, A17) at the external bus mode B. In the single-chip mode, these pins have the same functions as port P0. When the BYTE pin is set to "L" in the memory expansion mode or the microprocessor mode and external data bus has a 16-bit width, high-order data (D8 - D15) is input/output or an address (A8 - A15) is output. When the BYTE pin is "H" and an external data bus has an 8-bit width, only address (A8 - A15) is output. In the single-chip mode, these pins have the same functions as port P0. In the memory expansion mode or the microprocessor mode, low-order data (D0 - D7) is input/output or an address is output. When using the external bus mode A, the address is A16 - A23. When using the external bus mode B, the address is A0 - A7. In the single-chip mode, these pins have ___ same function_as port P0. In the memory expansion _ _ the _ ___ _ __ __ __ __ __ __ __ _ __ _ __ _ mode or the microprocessor mode, R/W,____BHE, ALE, and HLDA signals are output at the external ________ ____________ __ _____ _ _____ bus mode A, and WEL, WEH, ALE, and HLDA signals are output at the external bus mode B. In the single-chip mode, these pins have the same functions as____P0. In the memory expansion port ___ mode or the microprocessor mode, P40, P41, and P42 become HOLD and RDY input pins, and a clock 1 output pin, respectively. Functions of the other pins are the same as in the single-chip mode. However, in the memory expansion mode, P42 can be selected as an I/O port. In addition to having the same functions as port P0 in the single-chip mode, these pins also function as I/O pins for timers A0 to A3. In addition to having the same functions as port P0 in the single-chip mode, these pins also ___ ___ function as I/O pins for timer A4, input pins for external interrupt input (INT0 - INT2) and input pins for timers B0 to B2. P67 also functions as sub-clock SUB output pin. In addition to having the same functions as port P0 in the single-chip mode, these pins function as input pins for A-D converter. Additionally, P76 and P77 have the function as the output pin (XCOUT) and the input pin (XCIN) of the sub-clock (32 kHz) oscillation circuit, respectively. When P76 and P77 are used as the XCOUT and XCIN pins, connect a resonator or an oscillator between the both. In addition to having the same functions as port P0 in the single-chip mode, these pins also function as I/O pins for UART 0 and UART 1. Port P9 is an 8-bit I/O port. These ports are floating when reset. When writing to the port latch, these ports become the output mode. P90 - P93 also function as I/O port for UART 2. In addition to having the same functions as port P0 in the single-chip mode. P104 - P107 also __ __ function as input pins for key input interrupt input (Kl0 - Kl3). These pins should be left open.
Input I/O
P10 - P17
I/O port P1
I/O
P20 - P27
I/O port P2
I/O
P30 - P33
I/O port P3
I/O
P40 - P47
I/O port P4
I/O
P50 - P57 P60 - P67
I/O port P5 I/O port P6
I/O I/O
P70 - P77
I/O port P7
I/O
P80 - P87 P90 - P97
I/O port P8 Output port P9
I/O Output I/O Output
P100 - P107 I/O port P10 EVL0, EVL1
4
P
ion. hange. icat ecif ct to c l sp fina re subje ot a its a is n his tric lim e e: T otic param N e Som
IM REL
IN
Y AR
MITSUBISHI MICROCOMPUTERS
M37736MHLXXXHP
SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
BASIC FUNCTION BLOCKS
The M37736MHLXXXHP has the same functions as the M37736MHBXXXGP except for the package and the reset circuit. Refer to the section on the M37736MHBXXXGP.
ADDRESSING MODES
The M37736MHLXXXHP has 28 powerful addressing modes. Refer to the "7700 Family Software Manual" for the details.
MACHINE INSTRUCTION LIST RESET CIRCUIT
The microcomputer is released from the reset state when the RESET pin is returned to "H" level after holding it at "L" level with the power source voltage at 2.7 - 5.5 V. Program execution starts at the address formed by setting address A23 - A16 to 0016, A15 - A8 to the contents of address FFFF16, and A7 - A0 to the contents of address FFFE16. Figure 1 shows an example of a reset circuit. When the stabilized clock is input from the external to the main-clock oscillation circuit, the reset input voltage must be 0.55 V or less when the power source voltage reaches 2.7 V. When a resonator/oscillator is connected to the main-clock oscillation circuit, change the reset input voltage from "L" to "H" after the main-clock oscillation is fully stabilized. The status of the internal registers during reset is the same as the M37736MHBXXXGP's.
_____
The M37736MHLXXXHP has 103 machine instructions. Refer to the "7700 Family Software Manual" for the details.
DATA REQUIRED FOR MASK ROM ORDERING
Please send the following data for mask orders. (1) M37736MHLXXXHP mask ROM order confirmation form (2) 100P6Q mark specification form (100P6D mark specification form is substituted.) (3) ROM data (EPROM 3 sets)
Power on
VCC
RESET
2.7V 0V
VCC
RESET
0V
0.55V
Note. In this case, stabilized clock is input from the external to the main-clock oscillation circuit. Perform careful evalvation at the system design level before using.
Fig. 1 Example of a reset circuit
5
P
. . tion nge ifica to cha t pec al s subjec fin re a ot a is n limits his e: T ametric ic Not e par Som
IM REL
IN
Y AR
MITSUBISHI MICROCOMPUTERS
M37736MHLXXXHP
SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
ABSOLUTE MAXIMUM RATINGS
Symbol Vcc AVcc VI VI Parameter Conditions Power source voltage Analog power source voltage _____ Input voltage RESET, CNVss, BYTE Input voltage P00 - P07, P10 - P17, P20 - P27, P30 - P33, P40 - P47, P50 - P57, P60 - P67, P70 - P77, P80 - P87, P90 - P92, P100 - P107, VREF, XIN, BSEL Output voltage P00 - P07, P10 - P17, P20 - P27, P30 - P33, P40 - P47, P50 - P57, P60 - P67, P70 - P77, P80 - P87, _ P90 - P97, P100 - P107, XOUT, E Power dissipation Ta = 25 C Operating temperature Storage temperature Ratings -0.3 to +7 -0.3 to +7 -0.3 to +12 Unit V V V
-0.3 to Vcc + 0.3
V
VO
-0.3 to Vcc + 0.3 200 -40 to +85 -65 to +150
V mW C C
Pd Topr Tstg
RECOMMENDED OPERATING CONDITIONS (Vcc = 2.7 - 5.5 V, Ta = -40 to +85 C, unless otherwise noted)
Symbol Vcc AVcc Vss AVss VIH VIH VIH VIL VIL VIL IOH(peak) Parameter f(XIN) : Operating Power source voltage f(XIN) : Stopped, f(XCIN) = 32.768 kHz Analog power source voltage Power source voltage Analog power source voltage High-level input voltage P00 - P07, P30 - P33, P40 - P47, P50 - P57, P60 - P67, _____ P70 - P77, P80 - P87, P90 - P92, P100 - P107, XIN, RESET, CNVss, BYTE, BSEL, XCIN (Note 3) High-level input voltage P10 - P17, P20 - P27 (in single-chip mode) High-level input voltage P10 - P17, P20 - P27 (in memory expansion mode and microprocessor mode) Low-level input voltage P00 - P07, P30 - P33, P40 - P47, P50 - P57, _____ P60 - P67, P70 - P77, P80 - P87, P90 - P92, P100 - P107, XIN, RESET, CNVss, BYTE, BSEL, XCIN (Note 3) Low-level input voltage P10 - P17, P20 - P27 (in single-chip mode) Low-level input voltage P10 - P17, P20 - P27 (in memory expansion mode and microprocessor mode) High-level peak output current P00 - P07, P10 - P17, P20 - P27, P30 - P33, P40 - P47, P50 - P57, P60 - P67, P70 - P77, P80 - P87, P90 - P97, P100 - P107 High-level average output current P00 - P07, P10 - P17, P20 - P27, P30 - P33, P40 - P47, P50 - P57, P60 - P67, P70 - P77, P80 - P87, P90 - P97, P100 - P107 Low-level peak output current P00 - P07, P10 - P17, P20 - P27, P30 - P33, P40 - P43, P54 - P57, P60 - P67, P70 - P77, P80 - P87, P90 - P97, P104 - P107 Low-level peak output current P44 - P47, P100 - P103 Low-level average output current P00 - P07, P10 - P17, P20 - P27, P30 - P33, P40 - P43, P50 - P57, P60 - P67, P70 - P77, P80 - P87, P90 - P97, P104 - P107 Low-level average output current P44 - P47, P100 - P103 Main-clock oscillation frequency (Note 4) Sub-clock oscillation frequency Min. 2.7 2.7 Limits Typ. Max. 5.5 5.5 Unit V V V V Vcc Vcc Vcc 0.2Vcc 0.2Vcc 0.16Vcc -10 V V V V V V mA
Vcc 0 0 0.8 Vcc 0.8 Vcc 0.5 Vcc 0 0 0
IOH(avg)
-5
mA
IOL(peak) IOL(peak) IOL(avg) IOL(avg) f(XIN) f(XCIN)
10 16 5 12 12 50
mA mA mA mA MHz kHz
32.768
Notes 1. Average output current is the average value of a 100 ms interval. 2. The sum of IOL(peak) for ports P0, P1, P2, P3, P8, and P9 must be 80 mA or less, the sum of IOH(peak) for ports P0, P1, P2, P3, P8, and P9 must be 80 mA or less, the sum of IOL(peak) for ports P4, P5, P6, P7, and P10 must be 100 mA or less, and the sum of IOH(peak) for ports P4, P5, P6, P7, and P10 must be 80 mA or less. 3. Limits VIH and VIL for XCIN are applied when the sub clock external input selection bit = "1". 4. The maximum value of f(XIN) = 6 MHz when the main clock division selection bit = "1".
6
P
. . tion nge ifica to cha t pec al s subjec fin re a ot a is n limits This ric ice: aramet Not e p Som
IM REL
IN
Y AR
MITSUBISHI MICROCOMPUTERS
M37736MHLXXXHP
SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
ELECTRICAL CHARACTERISTICS (Vcc = 5 V, Vss = 0 V, Ta = -40 to +85 C, f(XIN) = 12 MHz, unless otherwise noted)
Symbol VOH VOH VOH Parameter High-level output voltage P00 - P07, P10 - P17, P20 - P27, P33, P40 - P47, P50 - P57, P60 - P67, P70 - P77, P80 - P87, P90 - P97, P100 - P107 High-level output voltage P00 - P07, P10 - P17, P20 - P27, P33 High-level output voltage P30 - P32 Test conditions
VCC = 5 V, IOH = -10 mA VCC = 3 V, IOH = -1 mA
Min. 3
Limits Typ.
Max.
Unit V
2.5 4.7 3.1 4.8 2.6 3.4 4.8 2.6 2 V 0.5 1.8 1.5 0.45 1.9 0.43 0.4 1.6 0.4 0.4 0.4 0.1 0.2 0.1 0.1 0.06 0.1 0.06 1 0.7 0.5 0.4 0.4 0.26 0.4 0.26 5 A 4 -5 A -4 -5 A -4 -0.25 -0.08 2 -0.5 -0.18 -1.0 -0.35 mA V V V V V V V V V V
_
VOH
High-level output voltage E Low-level output voltage P00 - P07, P10 - P17, P20 - P27, P33, P40 - P43, P50 - P57, P60 - P67, P70 - P77, P80 - P87, P90 - P97, P104 - P107 Low-level output voltage P44 - P47, P100 - P103 Low-level output voltage P00 - P07, P10 - P17, P20 - P27, P33 Low-level output voltage P30 - P32
VCC = 5 V, IOH = -400 A VCC = 5 V, IOH = -10 mA VCC = 5 V, IOH = -400 A VCC = 3 V, IOH = -1 mA VCC = 5 V, IOH = -10 mA VCC = 5 V, IOH = -400 A VCC = 3 V, IOH = -1 mA VCC = 5 V, IOL = 10 mA VCC = 3 V, IOL = 1 mA VCC = 5 V, IOL = 16 mA VCC = 3 V, IOL = 10 mA VCC = 5 V, IOL = 2 mA VCC = 5 V, IOL = 10 mA VCC = 5 V, IOL = 2 mA VCC = 3 V, IOL = 1 mA VCC = 5 V, IOL = 10 mA VCC = 5 V, IOL = 2 mA VCC = 3 V, IOL = 1 mA VCC = 5 V VCC = 3 V VCC = 5 V VCC = 3 V VCC = 5 V VCC = 3 V VCC = 5 V VCC = 3 V VCC = 5 V, VI = 5 V VCC = 3 V, VI = 3 V VCC = 5 V, VI = 0 V VCC = 3 V, VI = 0 V
VI = 0 V, without a pull-up transistor VI = 0 V, with a pull-up transistor VCC = 5 V VCC = 3 V VCC = 5 V VCC = 3 V
V
VOL
VOL VOL VOL
_
VOL
Low-level output voltage E
____ ___
V
VT+ - VT-
Hysteresis ___ ___ ____ - TA4IN, TB0IN - TB2IN, HOLD, RDY, TA0IN ____ ____ ____ INT0 - INT2, ADTRG, CTS0, CTS1, CTS2, CLK0, __ __ CLK1, CLK2, KI0 - KI3
_____
VT+ - VT- VT+ - VT- VT+ - VT- IIH
Hysteresis RESET Hysteresis XIN Hysteresis XCIN (When external clock is input) High-level input current P00 - P07, P10 - P17, P20 - P27, P30 - P33, P40 - P47, P50 - P57, P60 - P67, P70 - P77, _____ P80 - P87, P90 - P92, P100 - P107, XIN, RESET, CNVss, BYTE, BSEL Low-level input current P00 - P07, P10 - P17, P20 - P27, P30 - P33, P40 - P47, P50 - P53, P60, P61, P65 - P67, P70 _____P80 - P87, P90 - P92, P100 - P103, - P77, XIN, RESET, CNVss, BYTE, BSEL Low-level input current P62 - P64, P104 - P107
IIL
IIL
VRAM
RAM hold voltage
When clock is stopped.
7
P
. . tion nge ifica to cha t pec al s subjec fin re a ot a is n limits This ric ice: aramet Not e p Som
IM REL
IN
Y AR
MITSUBISHI MICROCOMPUTERS
M37736MHLXXXHP
SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
ELECTRICAL CHARACTERISTICS (Vcc = 5 V, Vss = 0 V, Ta = -40 to +85 C, unless otherwise noted)
Symbol Parameter Test conditions VCC = 5 V, f(XIN) = 12 MHz (square waveform), (f(f2) = 6 MHz), f(XCIN) = 32.768 kHz, in operating (Note 1) VCC = 3 V, f(XIN) = 12 MHz (square waveform), (f(f2) = 6 MHz), f(XCIN) = 32.768 kHz, in operating (Note 1) VCC = 3 V, f(XIN) = 12 MHz (square waveform), (f(f2) = 0.75 MHz), f(XCIN) : Stopped, in operating Min. Limits Typ. Max. Unit
4.5
9
mA
3
6
mA
ICC
Power source current
When single-chip mode, output pins are open, and other pins are VSS. VCC = 3 V, f(XIN) = 12 MHz (square waveform), f(XCIN) = 32.768 kHz, when a WIT instruction is executed (Note 2) VCC = 3 V, f(XIN) : Stopped, f(XCIN) = 32.768 kHz, in operating (Note 3) VCC = 3 V, f(XIN) : Stopped, f(XCIN) = 32.768 kHz, when a WIT instruction is executed (Note 4) Ta = 25 C, when clock is stopped Ta = 85 C, when clock is stopped
0.4
0.8
mA
6
12
A
30
60
A
3
6
A
1 20
A A
Notes 1. This applies when the main clock external input selection bit = "1", the main clock division selection bit = "0", and the signal output stop bit = "1". 2. This applies when the main clock external input selection bit = "1" and the system clock stop bit at wait state = "1". 3. This applies when CPU and the clock timer are operating with the sub clock (32.768 kHz) selected as the system clock. 4. This applies when the XCOUT drivability selection bit = "0" and the system clock stop bit at wait state = "1".
A-D CONVERTER CHARACTERISTICS
(VCC = AVCC = 5 V, VSS = AVSS = 0 V, Ta = -40 to +85 C, f(XIN) = 12 MHz, unless otherwise noted (Note)) Symbol -- -- RLADDER tCONV VREF VIA Parameter Resolution Absolute accuracy Ladder resistance Conversion time Reference voltage Analog input voltage Test conditions VREF = VCC VREF = VCC VREF = VCC Min. Limits Typ. Max. 10 3 25 VCC VREF Unit Bits LSB k s V V
10 19.6 2.7 0
Note. This applies when the main clock division selection bit = "0" and f(f2) = 6 MHz.
8
P
. . tion nge ifica to cha t pec al s subjec fin re a ot a is n limits This ric ice: aramet Not e p Som
IM REL
IN
Y AR
MITSUBISHI MICROCOMPUTERS
M37736MHLXXXHP
SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
TIMING REQUIREMENTS (VCC = 2.7 - 5.5 V, VSS = 0 V, Ta = -40 to +85 C, f(XIN) = 12 MHz, unless otherwise noted (Note 1)) Notes 1. This applies when the main clock division selection bit = "0" and f(f2) = 6 MHZ. 2. Input signal's rise/fall time must be 100 ns or less, unless otherwise noted. External clock input
Symbol tc tw(H) tw(L) tr tf Parameter External clock input cycle time (Note 3) External clock input high-level pulse width (Note 4) External clock input low-level pulse width (Note 4) External clock rise time External clock fall time Limits Min. 83 33 33 Max. Unit ns ns ns ns ns
15 15
Notes 3. When the main clock division selection bit = "1", the minimum value of tc = 166 ns. 4. When the main clock division selection bit = "1", values of tw(H) / tc and tw(L) / tc must be set to values from 0.45 through 0.55.
Single-chip mode
Symbol tsu(P0D-E) tsu(P1D-E) tsu(P2D-E) tsu(P3D-E) tsu(P4D-E) tsu(P5D-E) tsu(P6D-E) tsu(P7D-E) tsu(P8D-E) tsu(P10D-E) th(E-P0D) th(E-P1D) th(E-P2D) th(E-P3D) th(E-P4D) th(E-P5D) th(E-P6D) th(E-P7D) th(E-P8D) th(E-P10D) Port P0 input setup time Port P1 input setup time Port P2 input setup time Port P3 input setup time Port P4 input setup time Port P5 input setup time Port P6 input setup time Port P7 input setup time Port P8 input setup time Port P10 input setup time Port P0 input hold time Port P1 input hold time Port P2 input hold time Port P3 input hold time Port P4 input hold time Port P5 input hold time Port P6 input hold time Port P7 input hold time Port P8 input hold time Port P10 input hold time Parameter Limits Min. 200 200 200 200 200 200 200 200 200 200 0 0 0 0 0 0 0 0 0 0 Max. Unit ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns
Memory expansion mode and microprocessor mode
Symbol tsu(D-E) tsu(D-RDE) tsu(RDY- 1) tsu(HOLD- 1) th(E-D) th(RDE-D) th( 1-RDY) th( 1-HOLD) Parameter Data input setup time (external bus mode A) Data input setup time (external bus mode B) RDY input setup time ____ HOLD input setup time Data input hold time (external bus mode A) Data input hold time (external bus mode B) ___ RDY input hold time ____ HOLD input hold time
___
Limits Min. 50 50 80 80 0 0 0 0 Max.
Unit ns ns ns ns ns ns ns ns
9
P
. . tion nge ifica to cha t pec al s subjec fin re a ot a is n limits his e: T ametric ic Not e par Som
IM REL
IN
Y AR
MITSUBISHI MICROCOMPUTERS
M37736MHLXXXHP
SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
Timer A input
Symbol tc(TA) tw(TAH) tw(TAL)
(Count input in event counter mode) Parameter Limits Min. 250 125 125 Max. Unit ns ns ns
TAiIN input cycle time TAiIN input high-level pulse width TAiIN input low-level pulse width
Timer A input (Gating input in timer mode)
Symbol tc(TA) tw(TAH) tw(TAL) TAiIN input cycle time (Note) TAiIN input high-level pulse width (Note) TAiIN input low-level pulse width (Note) Parameter Limits Min. 666 333 333 Max. Unit ns ns ns
Note. Limits change depending on f(XIN). Refer to "DATA FORMULAS".
Timer A input (External trigger input in one-shot pulse mode)
Symbol tc(TA) tw(TAH) tw(TAL) TAiIN input cycle time (Note) TAiIN input high-level pulse width TAiIN input low-level pulse width Parameter Limits Min. 666 166 166 Max. Unit ns ns ns
Note. Limits change depending on f(XIN). Refer to "DATA FORMULAS".
Timer A input (External trigger input in pulse width modulation mode)
Symbol tw(TAH) tw(TAL) TAiIN input high-level pulse width TAiIN input low-level pulse width Parameter Limits Min. 166 166 Max. Unit ns ns
Timer A input (Up-down input in event counter mode)
Symbol tc(UP) tw(UPH) tw(UPL) tsu(UP-TIN) th(TIN-UP) TAiOUT input cycle time TAiOUT input high-level pulse width TAiOUT input low-level pulse width TAiOUT input setup time TAiOUT input hold time Parameter Limits Min. 3333 1666 1666 666 666 Max. Unit ns ns ns ns ns
Timer A input (Two-phase pulse input in event counter mode)
Symbol tc(TA) tsu(TAjIN-TAjOUT) tsu(TAjOUT-TAjIN) TAjIN input cycle time TAjIN input setup time TAjOUT input setup time Parameter Limits Min. 2000 500 500 Max. Unit ns ns ns
10
P
. . tion nge ifica to cha t pec al s subjec fin re a ot a is n limits his e: T ametric ic Not e par Som
IM REL
IN
Y AR
MITSUBISHI MICROCOMPUTERS
M37736MHLXXXHP
SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
Timer B input (Count input in event counter mode)
Symbol tc(TB) tw(TBH) tw(TBL) tc(TB) tw(TBH) tw(TBL) Parameter TBiIN input cycle time (one edge count) TBiIN input high-level pulse width (one edge count) TBiIN input low-level pulse width (one edge count) TBiIN input cycle time (both edges count) TBiIN input high-level pulse width (both edges count) TBiIN input low-level pulse width (both edges count) Limits Min. 250 125 125 500 250 250 Max. Unit ns ns ns ns ns ns
Timer B input (Pulse period measurement mode)
Symbol tc(TB) tw(TBH) tw(TBL) TBiIN input cycle time (Note) TBiIN input high-level pulse width (Note) TBiIN input low-level pulse width (Note) Parameter Limits Min. 666 333 333 Max. Unit ns ns ns
Note. Limits change depending on f(XIN). Refer to "DATA FORMULAS".
Timer B input (Pulse width measurement mode)
Symbol tc(TB) tw(TBH) tw(TBL) Parameter Limits Min. 666 333 333 Max. Unit ns ns ns TBiIN input cycle time (Note) TBiIN input high-level pulse width (Note) TBiIN input low-level pulse width (Note) Note. Limits change depending on f(XIN). Refer to "DATA FORMULAS".
A-D trigger input
Symbol
____
Parameter
ADTRG input cycle time (minimum allowable trigger) ____ ADTRG input low-level pulse width
Limits Min. 1333 166 Max.
Unit ns ns
tc(AD) tw(ADL)
Serial I/O
Symbol tc(CK) tw(CKH) tw(CKL) td(C-Q) th(C-Q) tsu(D-C) th(C-D) CLKi input cycle time CLKi input high-level pulse width CLKi input low-level pulse width TXDi output delay time TXDi hold time RXDi input setup time RXDi input hold time
____ ___
Parameter
Limits Min. 333 166 166 0 65 75 Max.
Unit ns ns ns ns ns ns ns
100
External interrupt INTi input, key input interrupt KIi input
Symbol
___
Parameter
INTi input high-level pulse width INTi input low-level pulse width __ KIi input low-level pulse width
___
Limits Min. 250 250 250 Max.
Unit ns ns ns
tw(INH) tw(INL) tw(KIL)
11
P
. . tion nge ifica to cha t pec al s subjec fin re a ot a is n limits This ric ice: aramet Not e p Som
IM REL
IN
Y AR
MITSUBISHI MICROCOMPUTERS
M37736MHLXXXHP
SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
DATA FORMULAS Timer A input (Gating input in timer mode)
Symbol tc(TA) tw(TAH) tw(TAL) TAiIN input cycle time TAiIN input high-level pulse width TAiIN input low-level pulse width Parameter Limits Min. 8 ! 109 2 * f(f2) 4 ! 109 2 * f(f2) 4 ! 109 2 * f(f2) Max. Unit ns ns ns
Timer A input (External trigger input in one-shot pulse mode)
Symbol tc(TA) TAiIN input cycle time Parameter Limits Min. 8 ! 109 2 * f(f2) Max. Unit ns
Timer B input (In pulse period measurement mode or pulse width measurement mode)
Symbol tc(TB) tw(TBH) tw(TBL) TBiIN input cycle time TBiIN input high-level pulse width TBiIN input low-level pulse width Parameter Limits Min. 8 ! 109 2 * f(f2) 4 ! 109 2 * f(f2) 4 ! 109 2 * f(f2) Max. Unit ns ns ns
Note. f(f2) represents the clock f2 frequency. For the relation to the main clock and sub clock, refer to Table 10 in data sheet "M37736MHBXXXGP".
12
P
ion. hange. icat ecif ct to c l sp fina re subje ot a its a is n his tric lim e e: T otic param N e Som
M ELI R
IN
Y AR
MITSUBISHI MICROCOMPUTERS
M37736MHLXXXHP
SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
SWITCHING CHARACTERISTICS
(VCC = 2.7 - 5.5 V, VSS = 0 V, Ta = - 40 to +85C, f(XIN) = 12 MHz, unless otherwise noted (Note))
Single-chip mode
Symbol td(E-P0Q) td(E-P1Q) td(E-P2Q) td(E-P3Q) td(E-P4Q) td(E-P5Q) td(E-P6Q) td(E-P7Q) td(E-P8Q) td(E-P9Q) td(E-P10Q) Parameter Port P0 data output delay time Port P1 data output delay time Port P2 data output delay time Port P3 data output delay time Port P4 data output delay time Port P5 data output delay time Port P6 data output delay time Port P7 data output delay time Port P8 data output delay time Port P9 data output delay time Port P10 data output delay time Test conditions Limits Min. Max. 300 300 300 300 300 300 300 300 300 300 300 Unit ns ns ns ns ns ns ns ns ns ns ns
Fig. 2
Note. This applies when the main clock division selection bit = "0" and f(f2) = 6 MHz.
P0 P1 P2 P3 P4 P5 P6 P7 P8 P9 P 10
1 E
50 pF
Fig. 2 Measuring circuit for ports P0 - P10 and
1
13
P
ion. hange. icat ecif ct to c l sp fina re subje a not sa is is ric limit t : Th tice arame No e p Som
M ELI R
IN
Y AR
MITSUBISHI MICROCOMPUTERS
M37736MHLXXXHP
SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
[External bus mode A] Memory expansion mode and microprocessor mode
(VCC = 2.7 - 5.5 V, VSS = 0 V, Ta = -40 to +85C, f(XIN) = 12 MHz (Note 1), unless otherwise noted) Symbol td(An-E) Address output delay time Parameter Test (Note 2) Wait mode conditions No wait Wait 1 Wait 0 No wait Wait 1 Wait 0 Limits Min. 20 182 20 162 40 No wait Wait 1 Wait 0 No wait Wait 1 Wait 0 No wait Wait 1 Wait 0 No wait Wait 1 Wait 0 40 123 10 93 9 40 Fig. 2 4 40 90 No wait Wait 1 Wait 0 40 131 298 10 53 No wait Wait 1 Wait 0 No wait Wait 1 Wait 0 20 182 20 182 33 33 0 Max. Unit ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns
td(A-E)
Address output delay time Address hold time ALE pulse width
th(E-An) tw(ALE)
tsu(A-ALE)
Address output setup time
th(ALE-A)
Address hold time
td(ALE-E) td(E-DQ) th(E-DQ) tw(EL) tpxz(E-DZ) tpzx(E-DZ) td(BHE-E)
ALE output delay time Data output delay time Data hold time
_
E pulse width
Floating start delay time Floating release delay time
___
BHE output delay time
td(R/W-E) th(E-BHE) th(E-R/W) td(E- 1) td( 1-HLDA)
_
R/W output delay time
___
BHE hold time _
R/W hold time 1 output delay time ____ HLDA output delay time
30 120
Notes 1. This applies when the main clock division selection bit = "0" and f(f2) = 6 MHz. 2. No wait : Wait bit = "1". Wait 1 : The external memory area is accessed with wait bit = "0" and wait selection bit = "1". Wait 0 : The external memory area is accessed with wait bit = "0" and wait selection bit = "0".
14
P
ge. ion. icat o chan t ecif l sp ubject fina re s a ot a is n limits his e: T ametric otic par N e Som
IM REL
IN
Y AR
MITSUBISHI MICROCOMPUTERS
M37736MHLXXXHP
SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
[External bus mode A] Memory expansion mode and microprocessor mode Bus timing data formulas (VCC = 2.7 - 5.5 V, VSS = 0 V, Ta = -40 to +85 C,
Symbol Parameter f(XIN) = 12 MHz (Max., Note), unless otherwise noted) Limits Min. 1 ! 109 - 63 2 * f(f2) 9 3 ! 10 - 68 2 * f(f2) 1 ! 109 - 63 2 * f(f2) 3 ! 109 - 88 2 * f(f2) 9 1 ! 10 - 43 2 * f(f2) 9 1 ! 10 - 43 2 * f(f2) 9 2 ! 10 - 43 2 * f(f2) 1 ! 109 - 73 2 * f(f2) 2 ! 109 - 73 2 * f(f2) 9 1! 2 * f(f2) 109 4 1 ! 109 2 * f(f2) 1 ! 109 2 * f(f2) 2 ! 109 2 * f(f2) 4 ! 109 2 * f(f2) 1 ! 109 2 * f(f2) 1 ! 109 2 * f(f2) 3 ! 109 2 * f(f2) 1 ! 109 2 * f(f2) 3 ! 109 2 * f(f2) 1 ! 109 2 * f(f2) 1 ! 109 2 * f(f2) 0 - 43 90 - 43 - 35 - 35 10 - 30 - 63 - 68 - 63 - 68 - 50 - 50 30 - 43 Max. Unit ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns
td(An-E)
Address output delay time
Wait mode No wait Wait 1 Wait 0 No wait Wait 1 Wait 0
td(A-E)
Address output delay time
th(E-An)
Address hold time No wait Wait 1 Wait 0 No wait Wait 1 Wait 0 No wait Wait 1 Wait 0 No wait Wait 1 Wait 0
tw(ALE)
ALE pulse width
tsu(A-ALE)
Address output setup time
th(ALE-A)
Address hold time
td(ALE-E)
ALE output delay time
td(E-DQ) th(E-DQ)
Data output delay time Data hold time
_
No wait Wait 1 Wait 0
tw(EL) tpxz(E-DZ) tpzx(E-DZ)
E pulse width
Floating start delay time Floating release delay time
___
td(BHE-E)
BHE output delay time
No wait Wait 1 Wait 0
_
td(R/W-E)
R/W output delay time
No wait Wait 1 Wait 0
___
th(E-BHE) th(E-R/W) td(E-
1)
BHE hold time
_
R/W hold time
1
output delay time
Notes 1. This applies when the main-clock division selection bit = "0". 2. f(f2) represents the clock f2 frequency. For the relation to the main clock and sub clock, refer to Table 10 in data sheet "M37736MHBXXXGP".
15
P
ion. hange. icat ecif ct to c l sp fina re subje a not sa is is ric limit t : Th tice arame No e p Som
M ELI R
IN
Y AR
MITSUBISHI MICROCOMPUTERS
M37736MHLXXXHP
SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
[External bus mode B] Memory expansion mode and microprocessor mode
(VCC = 2.7 - 5.5 V, VSS = 0 V, Ta = -40 to +85 C, f(XIN) = 12 MHz, unless otherwise noted (Note 1)) Symbol td(CS-WE) td(CS-RDE) th(WE-CS) th(RDE-CS) td(An-WE) td(An-RDE) td(A-WE) td(A-RDE) th(WE-An) th(RDE-An) tw(ALE) Chip-select output delay time Parameter Test (Note 2) Wait mode conditions No wait Wait 1 Wait 0 Limits Min. 20 182 4 No wait Wait 1 Wait 0 No wait Wait 1 Wait 0 20 182 20 162 40 No wait Wait 1 Wait 0 No wait Wait 1 Wait 0 No wait Wait 1 Wait 0 No wait Wait 1 Wait 0 40 123 Fig. 2 10 93 9 40 4 40 90 No wait Wait 1 Wait 0 40 131 298 10 No wait Wait 1 Wait 0 53 128 295 25 0 0 30 120 Max. Unit ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns
Chip-select hold time Address output delay time
Address output delay time Address hold time ALE pulse width
tsu(A-ALE)
Address output setup time
th(ALE-A)
Address hold time
td(ALE-WE) td(ALE-RDE) td(WE-DQ) th(WE-DQ) tw(WE) tpxz(RDE-DZ) tpzx(RDE-DZ) tw(RDE) td(RSMP-WE) td(RSMP-RDE) th( 1-RSMP) td(WE- 1) td(RDE- 1) td( 1-HLDA)
ALE output delay time Data output delay time Data hold time
___ ___
WEL/WEH pulse width
Floating start delay time Floating release delay time
___
RDE pulse width
____
RSMP output delay time
____
RSMP hold time
1
output delay time
____
HLDA output delay time
Notes 1. This applies when the main clock division selection bit = "0" and f(f2) = 6 MHz. 2. No wait : Wait bit = "1". Wait 1 : The external memory area is accessed with wait bit = "0" and wait selection bit = "1". Wait 0 : The external memory area is accessed with wait bit = "0" and wait selection bit = "0".
16
P
ion. hange. icat ecif ct to c l sp fina re subje a not sa is is ric limit t : Th tice arame No e p Som
M ELI R
IN
Y AR
MITSUBISHI MICROCOMPUTERS
M37736MHLXXXHP
SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
[External bus mode B] Bus timing data formulas (VCC = 2.7 - 5.5V, VSS = 0 V, Ta = -40 to +85 C, f(XIN) = 12 MHz (Max.), unless otherwise noted (Note1))
Symbol td(CS-WE) td(CS-RDE) th(WE-CS) th(RDE-CS) td(An-WE) td(An-RDE) Parameter Wait mode No wait Wait 1 Wait 0 Chip-select hold time No wait Wait 1 Wait 0 No wait Wait 1 Wait 0 Address hold time No wait Wait 1 Wait 0 No wait Wait 1 Wait 0 No wait Wait 1 Wait 0 td(ALE-WE) td(ALE-RDE) td(WE-DQ) th(WE-DQ) No wait Wait 1 Wait 0 Data output delay time Data hold time
___ ___
Chip-select output delay time
Limits Min. 1 ! 109 - 63 2 * f(f2) 9 3 ! 10 - 68 2 * f(f2) 4 1 ! 109 2 * f(f2) 3 ! 109 2 * f(f2) 1 ! 109 2 * f(f2) 3 ! 109 2 * f(f2) 1 ! 109 2 * f(f2) 1 ! 109 2 * f(f2) 2 ! 109 2 * f(f2) 1 ! 109 2 * f(f2) 2 ! 109 2 * f(f2) 9 1 ! 109 2 * f(f2) 4 1 ! 10 2 * f(f2)
9
Max.
Unit ns ns ns
- 63 - 68 - 63 - 88 - 43 - 43 - 43 - 73 - 73
ns ns ns ns ns ns ns ns ns ns
Address output delay time
td(A-WE) td(A-RDE) th(WE-An) th(RDE-An) tw(ALE)
Address output delay time
ALE pulse width
tsu(A-ALE)
Address output setup time
th(ALE-A)
Address hold time
- 43
ns ns
ALE output delay time
- 43 90
ns ns ns ns ns 10 ns ns ns ns ns ns 30 ns
No wait Wait 1 Wait 0
tw(WE) tpxz(RDE-DZ) tpzx(RDE-DZ)
WEL/WEH pulse width
1 ! 109 2 * f(f2) 2 ! 109 2 * f(f2) 4 ! 109 2 * f(f2) 1 ! 109 2 * f(f2) 2 ! 109 2 * f(f2) 4 ! 109 2 * f(f2) 1 ! 109 2 * f(f2) 0
- 43 - 35 - 35
Floating start delay time Floating release delay time
___
- 30 - 38 - 38
No wait Wait 1 Wait 0
tw(RDE)
RDE pulse width
td(RSMP-WE) - 58 RSMP output delay time td(RSMP-RDE) ____ th( 1-RSMP) RSMP hold time td(WE- 1) 1 output delay time 0 td(RDE- 1) Notes 1. This applies when the main clock division selection bit = "0". 2. f(f2) represents the clock f2 frequency. For the relation to the main clock and sub clock, refer to Table 10 in data sheet "M37736MHBXXXGP".
____
17
P
. . tion nge ifica to cha t pec al s subjec fin re a ot a is n limits his e: T ametric ic Not e par Som
IM REL
IN
Y AR
MITSUBISHI MICROCOMPUTERS
M37736MHLXXXHP
SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
TIMING DIAGRAM
XIN
tr
tf
tc
tw(H)
tw(L)
E
td(E-PiQ)
Port Pi output (i = 0 - 10)
tsu(PiD-E)
Port Pi input (i = 0 - 8, 10)
th(E-PiD)
18
P
. . tion nge ifica to cha t pec al s subjec fin re a ot a is n limits his e: T ametric ic Not e par Som
IM REL
IN
Y AR
MITSUBISHI MICROCOMPUTERS
M37736MHLXXXHP
SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
tc(TA) tw(TAH) TAiIN input
tw(TAL)
tc(UP) tw(UPH) TAiOUT input tw(UPL)
In event count mode
TAiOUT input (Up-down input) TAiIN input (when count by falling) TAiIN input (when count by rising)
th(TIN-UP)
tsu(UP-TIN)
In event counter mode (When two-phase pulse input is selected) TAjIN input
tsu(TAjIN-TAjOUT)
tc(TA)
tsu(TAjIN-TAjOUT) tsu(TAjOUT-TAjIN)
TAjOUT input
tsu(TAjOUT-TAjIN)
tc(TB) tw(TBH) TBiIN input tw(TBL)
19
P
. . tion nge ifica to cha t pec al s subjec fin re a ot a is n limits his e: T ametric ic Not e par Som
IM REL
IN
Y AR
MITSUBISHI MICROCOMPUTERS
M37736MHLXXXHP
SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
tc(AD) tw(ADL)
ADTRG input
tc(CK) tw(CKH) CLKi
tw(CKL)
th(C-Q) TxDi td(C-Q) RxDi tSU(D-C) th(C-D)
tw(INL)
INTi input Kli input
tw(INH) tw(KNL)
20
P
ion. hange. icat ecif ct to c l sp fina re subje a not sa is is ric limit t : Th tice arame No e p Som
M ELI R
IN
Y AR
MITSUBISHI MICROCOMPUTERS
M37736MHLXXXHP
SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
Memory expansion mode and microprocessor mode (When wait bit = "1")
1
E or RDE, WEL, WEH
RDY input
tsu(RDY-
1 )
th(
1-RDY)
( When wait bit = "0")
1
E or RDE, WEL, WEH
RDY input
tsu(RDY-
1 )
th(
1-RDY)
(When wait bit = "1" or "0" in common)
1
tsu(HOLD-
HOLD input
1 )
th(
1-HOLD)
td(
HLDA output
1 -HLDA)
td(
1-HLDA)
Test conditions * VCC = 2.7 - 5.5 V * Input timing voltage : V IL = 0.2 VCC, VIH = 0.8 VCC * Output timing voltage : V OL = 0.8 V, VOH = 2.0 V
21
P
. . tion nge ifica to cha t pec al s subjec fin re a ot a is n limits This ric ice: aramet Not e p Som
IM REL
IN
Y AR
MITSUBISHI MICROCOMPUTERS
M37736MHLXXXHP
SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
[External bus mode A]
Memory expansion mode and microprocessor mode (No wait : When wait bit = "1")
tw(L)
tw(H)
tf
tr
tc
XIN
1
td(E-
1)
td(Etw(EL)
1)
E
td(An-E)
th(E-An) Address Address Address
An
tw(ALE)
td(ALE-E)
ALE
th(ALE-A) tsu(A-ALE) th(E-DQ) tpxz(E-DZ) tpzx(E-DZ)
Am/Dm
Address
Data
Address th(E-D) tsu(D-E) Data
Address
td(E-DQ) td(A-E)
DmIN
th(E-BHE)
td(BHE-E) BHE
td(R/W-E)
th(E-R/W)
R/W
Test conditions * VCC = 2.7 - 5.5 V * Output timing voltage : VOL = 0.8 V, VOH = 2.0 V * Data input DmIN : VIL = 0.16 VCC, VIH = 0.5 VCC
22
P
ion. hange. icat ecif ct to c l sp fina re subje ot a its a is n his tric lim e e: T otic param N e Som
M ELI R
IN
Y AR
MITSUBISHI MICROCOMPUTERS
M37736MHLXXXHP
SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
[External bus mode A]
Memory expansion mode and microprocessor mode (Wait 1 : The external area is accessed when wait bit = "0" and wait selection bit = "1".)
tw(L) XIN
tw(H)
tf tr
tc
1
td(E-
E
1 )
td(E- tw(EL)
1 )
td(An-E) An
th(E-An) Address Address Address
tw(ALE) ALE
td(ALE-E)
th(ALE-A) tsu(A-ALE) Am/Dm Address Data th(E-DQ) tpxz(E-DZ) Address tpzx(E-DZ) Address
td(A-E)
td(E-DQ) tsu(D-E)
th(E-D)
DmIN
Data td(BHE-E) th(E-BHE)
BHE
td(R/W-E) R/W
th(E-R/W)
Test conditions * Vcc = 2.7 - 5.5 V * Output timing voltage : V OL = 0.8 V, VOH = 2.0 V * Data input DmIN : VIL = 0.16 Vcc, VIH = 0.5 Vcc
23
P
. . tion nge ifica to cha t pec al s subjec fin re a ot a is n limits This ric ice: aramet Not e p Som
IM REL
IN
Y AR
MITSUBISHI MICROCOMPUTERS
M37736MHLXXXHP
SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
[External bus mode A]
Memory expansion mode and microprocessor mode (Wait 0 : The external memory area is accessed when wait bit = "0" and wait selection bit = "0".)
tw(L) XIN
tw(H)
tf tr
tc
1
td(E-
E
1)
td(E- tw(EL)
1)
td(An-E) An Address
th(E-An) Address Address
tw(ALE) ALE
td(ALE-E)
tsu(A-ALE)
th(ALE-A) th(E-DQ) tpxz(E-DZ) Address tpzx(E-DZ) Address
Am/Dm
Address td(A-E)
Data td(E-DQ)
tsu(D-E) DmIN th(E-BHE) Data
th(E-D)
td(BHE-E)
BHE
td(R/W-E) R/W
th(E-R/W)
Test conditions * Vcc = 2.7 - 5.5 V * Output timing voltage : VOL = 0.8 V, VOH = 2.0 V * Data input DmIN : VIL = 0.16 Vcc, VIH = 0.5 Vcc
24
P
ion. hange. icat ecif ct to c l sp fina re subje a not sa is is ric limit t : Th tice arame No e p Som
M ELI R
IN
Y AR
MITSUBISHI MICROCOMPUTERS
M37736MHLXXXHP
SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
[External bus mode B]
Memory expansion and m icroprocessor mode (No wait : When wait bit = "1")
tw(L)
tw(H)
tf
tr
tc
XIN
1
td(WE-
1)
td(WE-
1)
td(RDE-
1)
td(RDE-
1)
CS0 - CS4 td(CS-WE) th(WE -CS) td(CS-RDE) th(RDE-CS)
An
td(An-WE) tw(ALE)
Address
td(An-RDE) td(ALE-WE) th(WE-An)
Address
Address
th(RDE -An)
ALE
th(ALE-A) tsu(A-ALE) th(WE-DQ) tpxz(RDE -DZ) tpzx(RDE -DZ) td(ALE-RDE)
Am/Dm
Address
Data
Address
td(A-RDE)
Address
td(WE-DQ) td(A-WE) tw(WE) WEL, WEH
th(RDE-D) tsu(D-RDE)
DmIN
Data
tw(RDE)
RDE th( td(RSMP -WE)
1 -RSMP)
td(RSMP -RDE)
RSMP
Test conditions * Vcc = 2.7 - 5.5 V * Output timing voltage : V OL = 0.8 V, VOH = 2.0 V * Data input DmIN : VIL = 0.16 VCC, VIH = 0.5 VCC
25
P
. . tion nge ifica to cha t pec al s subjec fin re a ot a is n limits This ric ice: aramet Not e p Som
IM REL
IN
Y AR
MITSUBISHI MICROCOMPUTERS
M37736MHLXXXHP
SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
[External bus mode B]
Memory expansion and m icroprocessor mode (Wait 1 : The external area is accessed when wait bit = "0" and wait selection bit = "1".)
tw(L) XIN
tw(H)
tf tr
tc
1
td(WE-
CS0 - CS4
1 )
td(WE-
1 )
td(RDE- td(RDE1 )
1 )
th(WE-CS) td(CS-RDE) td(CS-WE) An td(An-WE) tw(ALE) ALE th(ALE-A) tsu(A-ALE) Am/Dm Address Data td(ALE-RDE) th(WE-DQ) tpxz(RDE-DZ) tpzx(RDE-DZ) Address Address Address td(An-RDE) th(WE-An) td(ALE-WE) th(RDE-An) th(RDE-CS)
Address
td(A-WE)
td(WE-DQ) tw(WE)
td(A-RDE)
WEL, WEH
th(RDE-D) tsu(D-RDE) Data
DmIN
tw(RDE)
RDE
th(
RSMP
1-RSMP)
td(RSMP-WE)
td(RSMP-RDE)
Test conditions * Vcc = 2.7 - 5.5 V * Output timing voltage : V OL = 0.8 V, VOH = 2.0 V * Data input DmIN : VIL = 0.16 VCC, VIH = 0.5 VCC
26
P
. . tion nge ifica to cha t pec al s subjec fin re a ot a is n limits This ric ice: aramet Not e p Som
IM REL
IN
Y AR
MITSUBISHI MICROCOMPUTERS
M37736MHLXXXHP
SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
[External bus mode B]
Memory expansion and microprocessor mode (Wait 0 : The external memory are is accessed when wait bit = "0" and wait selection bit = "0".)
tw(L) XIN
tw(H)
tf tr
tc
1
td(WE-
1 )
td(WE-
1 )
td(RDE-
1 )
td(RDE-
1 )
CS0 - CS4
td(CS-WE)
th(WE-CS)
td(CS-RDE) th(RDE-CS)
An td(An-WE) tw(ALE) ALE
Address td(An-RDE) td(ALE-WE) th(WE-An)
Address
Address
th(RDE-An)
td(ALE-RDE) tsu(A-ALE)
th(ALE-A)
th(WE-DQ) Address td(A-RDE)
tpxz(RDE-DZ)
tpzx(RDE-DZ) Address
Am/Dm
Address td(A-WE)
Data td(WE-DQ)
tw(WE)
WEL, WEH
tsu(D-RDE) Data
th(RDE-D)
DmIN
tw(RDE)
RDE
td(RSMP-WE)
RSMP
th(
1-RSMP)
td(RSMP-RDE)
Test conditions * Vcc = 2.7 - 5.5 V * Output timing voltage : V OL = 0.8 V, VOH = 2.0 V * Data input DmIN : VIL = 0.16 VCC, VIH = 0.5 VCC
27
P
. . tion nge ifica to cha t pec al s subjec fin re a ot a is n limits This ric ice: aramet Not e p Som
IM REL
IN
Y AR
MITSUBISHI MICROCOMPUTERS
M37736MHLXXXHP
SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
PACKAGE OUTLINE
Keep safety first in your circuit designs!
Mitsubishi Electric Corporation puts the maximum effort into making semiconductor products better and more reliable, but there is always the possibility that trouble may occur with them. Trouble with semiconductors may lead to personal injury, fire or property damage. Remember to give due consideration to safety when making your circuit designs, with appropriate measures such as (i) placement of substitutive, auxiliary circuits, (ii) use of non-flammable material or (iii) prevention against any malfunction or mishap.
Notes regarding these materials
These materials are intended as a reference to assist our customers in the selection of the Mitsubishi semiconductor product best suited to the customer's application; they do not convey any license under any intellectual property rights, or any other rights, belonging to Mitsubishi Electric Corporation or a third party. Mitsubishi Electric Corporation assumes no responsibility for any damage, or infringement of any third-party's rights, originating in the use of any product data, diagrams, charts or circuit application examples contained in these materials. All information contained in these materials, including product data, diagrams and charts, represent information on products at the time of publication of these materials, and are subject to change by Mitsubishi Electric Corporation without notice due to product improvements or other reasons. It is therefore recommended that customers contact Mitsubishi Electric Corporation or an authorized Mitsubishi Semiconductor product distributor for the latest product information before purchasing a product listed herein. Mitsubishi Electric Corporation semiconductors are not designed or manufactured for use in a device or system that is used under circumstances in which human life is potentially at stake. Please contact Mitsubishi Electric Corporation or an authorized Mitsubishi Semiconductor product distributor when considering the use of a product contained herein for any specific purposes, such as apparatus or systems for transportation, vehicular, medical, aerospace, nuclear, or undersea repeater use. The prior written approval of Mitsubishi Electric Corporation is necessary to reprint or reproduce in whole or in part these materials. If these products or technologies are subject to the Japanese export control restrictions, they must be exported under a license from the Japanese government and cannot be imported into a country other than the approved destination. Any diversion or reexport contrary to the export control laws and regulations of Japan and/or the country of destination is prohibited. Please contact Mitsubishi Electric Corporation or an authorized Mitsubishi Semiconductor product distributor for further details on these materials or the products contained therein.
(c) 1996 MITSUBISHI ELECTRIC CORP. H-LF456-A KI-9611 Printed in Japan (ROD) New publication, effective Nov. 1996. 28 Specifications subject to change without notice.
REVISION DESCRIPTION LIST
Rev. No. 1.00 2.00 First Edition The following are revised:
Page P4 P100 - P107 P100 - P107 EVL0, EVL1 Output port P10 - I/O Output Previous Version
M37736MHLXXXHP Datasheet
Revision Description Rev. date 970507 980731
Revised Version
P100 - P107 EVL0, EVL1
I/O port P10 -
I/O Output
P5 Right column Line 2
The M37736MHLXXXHP has 28 powerful addressing modes. Refer to the SINGLE-CHIP 16BIT MICROCOMPUTERS DATA BOOK for the details of each addressing mode.
The M37736MHLXXXHP has 28 powerful addressing modes. Refer to the "7700 Family Software Manual" for the details.
MACHINE INSTRUCTION LIST MACHINE INSTRUCTION LIST
The M37736MHLXXXHP has 103 machine instructions. Refer to the SINGLE-CHIP 16-BIT MICROCOMPUTERS DATA BOOK for details. P9 Memory expansion mode and microprocessor mode The M37736MHLXXXHP has 103 machine instructions. Refer to the "7700 Family Software Manual" for the details.
Previous Version Limits Min. 80 80 Max.
Symbol tsu(D-E) tsu(D-RDE)
Parameter Data input setup time (external bus mode A) Data input setup time (external bus mode B)
Unit ns ns
Revised Version Limits Min. 50 50 Max.
Symbol tsu(D-E) tsu(D-RDE)
Parameter Data input setup time (external bus mode A) Data input setup time (external bus mode B)
Unit ns ns
(1)

▲Up To Search▲

Price & Availability of M37736EHLXXXHP

	To Download M37736EHLXXXHP Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .